chan_dongle

This site is best viewed in a modern browser with JavaScript enabled.

enamchuk

darkside Can you share it? I don't understand portugal language

darkside

enamchuk i trie afternoon to made a English tutorial, and share the rpm package. But now i can't i only have mobile phone and do not have material to translate.

darkside

enamchuk That's rock

First of all find what version of asterisk you are running, on console type: rasterisk -x "core show version"

If your version is lower than version 11.21-0 update the asterisk with the command: yum update
asterisk -y

install the driver for dongle , the link that i provide is for 64bits and for version of asterisk 11.25-0rev34:

rpm -ivh http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm

that command, makes the download from the source and install it.

Enter inside of the CLI of the asterisk, with the command: rasterisk

set verbose mode with command: core set verbose 3

Execute the command: module unload chan_dongle.so
and then: module load chan_dongle.so

Run: yum install usb_modeswitch -y

If you see the following error message in your Asterisk perform the following steps.
Chan_dongle.c: unable to open / dev / ttyUSB1: Permission denied

Run: vim /etc/udev/rules.d/92-dongle.rules and add the content below.

KERNEL == "ttyUSB *", MODE = "0666", OWNER = "asterisk", GROUP = "uucp"

Save the file.

Restart the server

When plugging in the first time modem make sure it's recognized in / dev, most modems
Recognize 3 ttyUSB, to verify that your modem recognized correctly execute.
Run: ls -la / dev / ttyUSB *

Enter now into the asterisk CLI and run the command: module reload chan_dongle.so
To check if the modens have been recognized type: dongle show devices
you see information about yor firmware, imei, operator, imsi, etc

for now you need to edite the file in /etc/asterisk/dongle.conf, and change the imei of your dongle and the imsi

Setup a new custom trunk for your dongle under Connectivity → Trunks → Add Custom Trunk and set these values:

Trunk Name: to-my-cellphone
Outbound CallerID: Your SIM card number with country code (with a plus sign at the beginning)
Custom Dial String: dongle/dongle0/$OUTNUM$

set a outbound route withe a name, a dial patern and Trunk Sequence for Matched Routes

I hope this help you.

Mlopes

enamchuk

darkside Thanks! :-)

jlebr

darkside

hi. my issabel is: Asterisk 13.22.0 built by issabel @ issabeldev8 on a x86_64 running Linux on 2018-08-30 13:58:00 UTC

but when I execute the command: rpm -ivh http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm

Error: Dependency error:
asterisk-devel is required by chan_dongle-asterisk-11.25.0-rev34.x86_64

I run yum install asterisk-devel, the server is reinstalled, I return to give it to download the program and I get dependency error again.

could you help me?

emendoza

hello darkside , I'm very new to all of pbx issabel, I'm trying to connect my huawei e1752 to receive and make calls. I followed your instructions but I could not connect the device. my huawei e1752, can make and receive calls from Mobile Partner, I've already done it. but I want to make a telephone exchange with Issabel to call and receive. I'd appreciate your help

issabelPBX * CLI> dongle show device state dongle0
-------------- Status -------------
  Device: dongle0
  State: Not connected Start scheduled
  Audio: / dev / ttyUSB1
  Data: / dev / ttyUSB2
  Voice: No
  SMS: No
  Manufacturer:
  Model:
  Firmware:
  IMEI:
  IMSI:
  GSM Registration Status: Unknown
  RSSI: 0, <= -113 dBm
  Mode: No Service
  Submode: No service
  Provider Name: NONE
  Location area code:
  Cell ID:
  Subscriber Number: Unknown
  SMS Service Center:
  Use UCS-2 encoding: No
  USSD use 7 bit encoding: No
  USSD use UCS-2 decoding: Yes
  Tasks in queue: 0
  Commands in queue: 0
  Call Waiting: Disabled
  Current device state: stop
  Desired device state: start
  When change state: now
  Calls / Channels: 0
    Active: 0
    Held: 0
    Dialing: 0
    Alerting: 0
    Incoming: 0
    Waiting: 0
    Releasing: 0
    Initializing: 0

VERSION ISSABEL

Kernel
Linux (x86_64) -3.10.0-862.6.3.el7.x86_64

Issabel
   issabel-4.0.0-1
   issabel-addons-4.0.0-4
   issabel-agenda-4.0.0-3
   issabel-asterisk-sounds-1.2.3-2
   issabel-callcenter-4.0.0-4
   issabel-email_admin-4.0.0-2
   issabel-endpointconfig2-4.0.0-3
   issabel-extras-4.0.0-4
   issabel-fax-4.0.0-1
   issabel-firstboot-4.0.0-3
   issabel-framework-4.0.0-6
   issabel-my_extension-4.0.0-1
   issabel-pbx-4.0.0-5
   issabel-portknock-4.0.0-2
   issabel-reports-4.0.0-3
   issabel-security-4.0.0-6
   issabel-system-4.0.0-7

RoundCubeMail
RoundCubeMail-0.3.1-13

Mail
postfix-2.10.1-6.el7
cyrus-imapd-2.4.17-13.el7

IM
openfire- (not installed) -

IssablPBX
issabelPBX-2.11.0-47

Asterisk
   asterisk11-11.25.3-3.el7.centos
   asterisk11-addons-11.25.3-3.el7.centos
   asterisk11-devel-11.25.3-3.el7.centos
   asterisk-es-sounds-1.0.0-0.el7.centos
   asterisk-fr-sounds-1.0.0-0.el7.centos
   asterisk-perl-1.03-1.el7.centos

FAX
hylafax-4.3.11-1rh7
iaxmodem-1.3.0-2.el7.centos

DRIVERS
   dahdi-2.11.1-1.el7.centos
   rhino-0.99.7-0
   wanpipe-util-7.0.25.1-0

emendoza

Thank you ggrraay . After a tough battle, I managed to get virtualbox to show the Huawei e1752 device. Solution: remove all device drivers, mobile partner and datacard. then install the default drivers of the e1752 CD that run when you connect the device to the USB port and then EUREKA! my device is shown in the virtualbox as usb. I will continue showing results of the commands:
lsusb

ls / dev / ttyUSB *

[root @ issabel ~] # lsusb
Bus 001 Device 002: ID 12d1: 1406 Huawei Technologies Co., Ltd. E1750
Bus 001 Device 001: ID 1d6b: 0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b: 0001 Linux Foundation 1.1 root hub

[root @ issabel ~] # ls / dev / ttyUSB *

/ dev / ttyUSB0 / dev / ttyUSB1

I will continue trying the instructions of darkside

Stiven

darkside The link http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm does not work

balkin77

Good morning, I installed chan-dongle in issabel 4, following the steps above, preo when I enter the console asterisk and charge the module returns this error, someone can help me.
I have tried several things, I have searched for the imsi, I can not find it, I have also checked that this USB modem is unlocked, I have checked that it has coverage, and that's fine, as the error said:
ERROR [3573]: at_response.c: 364 at_response_error: [dongle0] Getting IMSI number failed

Thanks for the help you can give me

balkin77

Good afternoon, I answer myself, the problem had it in the SIM, I activated it and I have modified the modem firmware to a more modern version, now I get calls but I have a big problem, nothing is heard, apparently there is some problem with the codec negotiation, I get this error:

WARNING[4794][C-00000009]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000008] Don't know how to indicate condition 22
[2018-04-23 14:14:43] WARNING[4794][C-00000009]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000008] Don't know how to indicate condition 22
[2018-04-23 14:14:43] WARNING[4794][C-00000009]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000008] Don't know how to indicate condition 33
[2018-04-23 14:14:44] WARNING[4794][C-00000009]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000008] Don't know how to indicate condition 33

i think that it is for voice codecs, someone with same issue?

balkin77

Good morning, attached asterisk capture of a call made from issabel by a dongle, the call is made but I do not have audio in any way.

-- Called dongle/dongle0/655463605
-- Dongle/dongle0-0100000003 is making progress passing it to SIP/1101-00000001
[2018-04-26 11:53:11] ERROR[4423]: at_response.c:472 at_response_error: [dongle0] AT^DDSETEX failed
> 0x7fb224033d70 -- Strict RTP switching to RTP remote address 172.16.0.211:4000 as source
> 0x7fb224033d70 -- Strict RTP learning complete - Locking on source address 172.16.0.211:4000
== Everyone is busy/congested at this time (1:1/0/0)
-- Executing [s@macro-dialout-trunk:31] NoOp("SIP/1101-00000001", "Dial failed for some reason with DIALSTATUS = BUSY and HANGUPCAUSE = 17") in new stack
-- Executing [s@macro-dialout-trunk:32] GotoIf("SIP/1101-00000001", "0?continue,1:s-BUSY,1") in new stack
-- Goto (macro-dialout-trunk,s-BUSY,1)
-- Executing [s-BUSY@macro-dialout-trunk:1] NoOp("SIP/1101-00000001", "Dial failed due to trunk reporting BUSY - giving up") in new stack
-- Executing [s-BUSY@macro-dialout-trunk:2] PlayTones("SIP/1101-00000001", "busy") in new stack
-- Executing [s-BUSY@macro-dialout-trunk:3] Busy("SIP/1101-00000001", "20") in new stack
== Spawn extension (macro-dialout-trunk, s-BUSY, 3) exited non-zero on 'SIP/1101-00000001' in macro 'dialout-trunk'
== Spawn extension (from-internal, 655463605, 5) exited non-zero on 'SIP/1101-00000001'
-- Executing [h@from-internal:1] Hangup("SIP/1101-00000001", "") in new stack
== Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/1101-00000001'
-- Executing [1101@default:1] Set("Dongle/dongle0-0100000004", "RINGTIMER=15") in new stack
-- Executing [1101@default:2] Macro("Dongle/dongle0-0100000004", "exten-vm,novm,1101,0,0,0") in new stack
-- Executing [s@macro-exten-vm:1] Macro("Dongle/dongle0-0100000004", "user-callerid,") in new stack
-- Executing [s@macro-user-callerid:1] Set("Dongle/dongle0-0100000004", "TOUCH_MONITOR=1524736430.10") in new stack
-- Executing [s@macro-user-callerid:2] Set("Dongle/dongle0-0100000004", "AMPUSER=961152743") in new stack
-- Executing [s@macro-user-callerid:3] GotoIf("Dongle/dongle0-0100000004", "0?report") in new stack
-- Executing [s@macro-user-callerid:4] ExecIf("Dongle/dongle0-0100000004", "1?Set(REALCALLERIDNUM=961152743)") in new stack
-- Executing [s@macro-user-callerid:5] Set("Dongle/dongle0-0100000004", "AMPUSER=") in new stack
-- Executing [s@macro-user-callerid:6] GotoIf("Dongle/dongle0-0100000004", "0?limit") in new stack
-- Executing [s@macro-user-callerid:7] Set("Dongle/dongle0-0100000004", "AMPUSERCIDNAME=") in new stack
-- Executing [s@macro-user-callerid:8] GotoIf("Dongle/dongle0-0100000004", "1?report") in new stack
-- Goto (macro-user-callerid,s,15)
-- Executing [s@macro-user-callerid:15] GotoIf("Dongle/dongle0-0100000004", "0?continue") in new stack
-- Executing [s@macro-user-callerid:16] Set("Dongle/dongle0-0100000004", "TTL=64") in new stack
-- Executing [s@macro-user-callerid:17] GotoIf("Dongle/dongle0-0100000004", "1?continue") in new stack
-- Goto (macro-user-callerid,s,28)
-- Executing [s@macro-user-callerid:28] Set("Dongle/dongle0-0100000004", "CALLERID(number)=961152743") in new stack
-- Executing [s@macro-user-callerid:29] Set("Dongle/dongle0-0100000004", "CALLERID(name)=dongle0") in new stack
-- Executing [s@macro-user-callerid:30] Set("Dongle/dongle0-0100000004", "CDR(cnum)=961152743") in new stack
-- Executing [s@macro-user-callerid:31] Set("Dongle/dongle0-0100000004", "CDR(cnam)=dongle0") in new stack
-- Executing [s@macro-user-callerid:32] Set("Dongle/dongle0-0100000004", "CHANNEL(language)=en") in new stack
-- Executing [s@macro-exten-vm:2] Set("Dongle/dongle0-0100000004", "RingGroupMethod=none") in new stack
-- Executing [s@macro-exten-vm:3] Set("Dongle/dongle0-0100000004", "EXTTOCALL=1101") in new stack
-- Executing [s@macro-exten-vm:4] Set("Dongle/dongle0-0100000004", "PICKUPMARK=1101") in new stack
-- Executing [s@macro-exten-vm:5] Set("Dongle/dongle0-0100000004", "RT=") in new stack
-- Executing [s@macro-exten-vm:6] Gosub("Dongle/dongle0-0100000004", "sub-record-check,s,1(exten,1101,)") in new stack
-- Executing [s@sub-record-check:1] Set("Dongle/dongle0-0100000004", "REC_POLICY_MODE_SAVE=") in new stack
-- Executing [s@sub-record-check:2] GotoIf("Dongle/dongle0-0100000004", "1?check") in new stack
-- Goto (sub-record-check,s,7)
-- Executing [s@sub-record-check:7] Set("Dongle/dongle0-0100000004", "MON_FMT=WAV") in new stack
-- Executing [s@sub-record-check:8] GotoIf("Dongle/dongle0-0100000004", "1?next") in new stack
-- Goto (sub-record-check,s,11)
-- Executing [s@sub-record-check:11] ExecIf("Dongle/dongle0-0100000004", "0?Return()") in new stack
-- Executing [s@sub-record-check:12] ExecIf("Dongle/dongle0-0100000004", "0?Set(REC_POLICY_MODE=)") in new stack
-- Executing [s@sub-record-check:13] GotoIf("Dongle/dongle0-0100000004", "0?exten,1") in new stack
-- Executing [s@sub-record-check:14] Set("Dongle/dongle0-0100000004", "REC_STATUS=INITIALIZED") in new stack
-- Executing [s@sub-record-check:15] Set("Dongle/dongle0-0100000004", "NOW=1524736430") in new stack
-- Executing [s@sub-record-check:16] Set("Dongle/dongle0-0100000004", "DAY=26") in new stack
-- Executing [s@sub-record-check:17] Set("Dongle/dongle0-0100000004", "MONTH=04") in new stack
-- Executing [s@sub-record-check:18] Set("Dongle/dongle0-0100000004", "YEAR=2018") in new stack
-- Executing [s@sub-record-check:19] Set("Dongle/dongle0-0100000004", "TIMESTR=20180426-115350") in new stack
-- Executing [s@sub-record-check:20] Set("Dongle/dongle0-0100000004", "FROMEXTEN=961152743") in new stack
-- Executing [s@sub-record-check:21] Set("Dongle/dongle0-0100000004", "CALLFILENAME=exten-1101-961152743-20180426-115350-1524736430.10") in new stack
-- Executing [s@sub-record-check:22] Goto("Dongle/dongle0-0100000004", "exten,1") in new stack
-- Goto (sub-record-check,exten,1)
-- Executing [exten@sub-record-check:1] GotoIf("Dongle/dongle0-0100000004", "0?callee") in new stack
-- Executing [exten@sub-record-check:2] Set("Dongle/dongle0-0100000004", "REC_POLICY_MODE=dontcare") in new stack
-- Executing [exten@sub-record-check:3] GotoIf("Dongle/dongle0-0100000004", "1?caller") in new stack
-- Goto (sub-record-check,exten,10)
-- Executing [exten@sub-record-check:10] Set("Dongle/dongle0-0100000004", "REC_POLICY_MODE=") in new stack
-- Executing [exten@sub-record-check:11] GosubIf("Dongle/dongle0-0100000004", "0?record,1(exten,1101,961152743)") in new stack
-- Executing [exten@sub-record-check:12] Return("Dongle/dongle0-0100000004", "") in new stack
-- Executing [s@macro-exten-vm:7] Macro("Dongle/dongle0-0100000004", "dial-one,,Ttr,1101") in new stack
-- Executing [s@macro-dial-one:1] Set("Dongle/dongle0-0100000004", "DEXTEN=1101") in new stack
-- Executing [s@macro-dial-one:2] Set("Dongle/dongle0-0100000004", "DIALSTATUS_CW=") in new stack
-- Executing [s@macro-dial-one:3] GosubIf("Dongle/dongle0-0100000004", "0?screen,1()") in new stack
-- Executing [s@macro-dial-one:4] GosubIf("Dongle/dongle0-0100000004", "0?cf,1()") in new stack
-- Executing [s@macro-dial-one:5] GotoIf("Dongle/dongle0-0100000004", "1?skip1") in new stack
-- Goto (macro-dial-one,s,8)
-- Executing [s@macro-dial-one:8] GotoIf("Dongle/dongle0-0100000004", "0?nodial") in new stack
-- Executing [s@macro-dial-one:9] GotoIf("Dongle/dongle0-0100000004", "0?continue") in new stack
-- Executing [s@macro-dial-one:10] Set("Dongle/dongle0-0100000004", "EXTHASCW=ENABLED") in new stack
-- Executing [s@macro-dial-one:11] GotoIf("Dongle/dongle0-0100000004", "0?next1:cwinusebusy") in new stack
-- Goto (macro-dial-one,s,23)
-- Executing [s@macro-dial-one:23] GotoIf("Dongle/dongle0-0100000004", "1?next3:continue") in new stack
-- Goto (macro-dial-one,s,24)
-- Executing [s@macro-dial-one:24] ExecIf("Dongle/dongle0-0100000004", "0?Set(DIALSTATUS_CW=BUSY)") in new stack
-- Executing [s@macro-dial-one:25] GotoIf("Dongle/dongle0-0100000004", "0?nodial") in new stack
-- Executing [s@macro-dial-one:26] GosubIf("Dongle/dongle0-0100000004", "1?dstring,1():dlocal,1()") in new stack
-- Executing [dstring@macro-dial-one:1] Set("Dongle/dongle0-0100000004", "DSTRING=") in new stack
-- Executing [dstring@macro-dial-one:2] Set("Dongle/dongle0-0100000004", "DEVICES=1101") in new stack
-- Executing [dstring@macro-dial-one:3] ExecIf("Dongle/dongle0-0100000004", "0?Return()") in new stack
-- Executing [dstring@macro-dial-one:4] ExecIf("Dongle/dongle0-0100000004", "0?Set(DEVICES=101)") in new stack
-- Executing [dstring@macro-dial-one:5] Set("Dongle/dongle0-0100000004", "LOOPCNT=1") in new stack
-- Executing [dstring@macro-dial-one:6] Set("Dongle/dongle0-0100000004", "ITER=1") in new stack
-- Executing [dstring@macro-dial-one:7] Set("Dongle/dongle0-0100000004", "THISDIAL=SIP/1101") in new stack
-- Executing [dstring@macro-dial-one:8] GosubIf("Dongle/dongle0-0100000004", "1?zap2dahdi,1()") in new stack
-- Executing [zap2dahdi@macro-dial-one:1] ExecIf("Dongle/dongle0-0100000004", "0?Return()") in new stack
-- Executing [zap2dahdi@macro-dial-one:2] Set("Dongle/dongle0-0100000004", "NEWDIAL=") in new stack
-- Executing [zap2dahdi@macro-dial-one:3] Set("Dongle/dongle0-0100000004", "LOOPCNT2=1") in new stack
-- Executing [zap2dahdi@macro-dial-one:4] Set("Dongle/dongle0-0100000004", "ITER2=1") in new stack
-- Executing [zap2dahdi@macro-dial-one:5] Set("Dongle/dongle0-0100000004", "THISPART2=SIP/1101") in new stack
-- Executing [zap2dahdi@macro-dial-one:6] ExecIf("Dongle/dongle0-0100000004", "0?Set(THISPART2=DAHDI/1101)") in new stack
-- Executing [zap2dahdi@macro-dial-one:7] Set("Dongle/dongle0-0100000004", "NEWDIAL=SIP/1101&") in new stack
-- Executing [zap2dahdi@macro-dial-one:8] Set("Dongle/dongle0-0100000004", "ITER2=2") in new stack
-- Executing [zap2dahdi@macro-dial-one:9] GotoIf("Dongle/dongle0-0100000004", "0?begin2") in new stack
-- Executing [zap2dahdi@macro-dial-one:10] Set("Dongle/dongle0-0100000004", "THISDIAL=SIP/1101") in new stack
-- Executing [zap2dahdi@macro-dial-one:11] Return("Dongle/dongle0-0100000004", "") in new stack
-- Executing [dstring@macro-dial-one:9] Set("Dongle/dongle0-0100000004", "DSTRING=SIP/1101&") in new stack
-- Executing [dstring@macro-dial-one:10] Set("Dongle/dongle0-0100000004", "ITER=2") in new stack
-- Executing [dstring@macro-dial-one:11] GotoIf("Dongle/dongle0-0100000004", "0?begin") in new stack
-- Executing [dstring@macro-dial-one:12] Set("Dongle/dongle0-0100000004", "DSTRING=SIP/1101") in new stack
-- Executing [dstring@macro-dial-one:13] Return("Dongle/dongle0-0100000004", "") in new stack
-- Executing [s@macro-dial-one:27] GotoIf("Dongle/dongle0-0100000004", "0?nodial") in new stack
-- Executing [s@macro-dial-one:28] GotoIf("Dongle/dongle0-0100000004", "0?skiptrace") in new stack
-- Executing [s@macro-dial-one:29] GosubIf("Dongle/dongle0-0100000004", "1?ctset,1():ctclear,1()") in new stack
-- Executing [ctset@macro-dial-one:1] Set("Dongle/dongle0-0100000004", "DB(CALLTRACE/1101)=961152743") in new stack
-- Executing [ctset@macro-dial-one:2] Return("Dongle/dongle0-0100000004", "") in new stack
-- Executing [s@macro-dial-one:30] Set("Dongle/dongle0-0100000004", "D_OPTIONS=Ttr") in new stack
-- Executing [s@macro-dial-one:31] ExecIf("Dongle/dongle0-0100000004", "0?SIPAddHeader(Alert-Info: )") in new stack
-- Executing [s@macro-dial-one:32] ExecIf("Dongle/dongle0-0100000004", "0?SIPAddHeader()") in new stack
-- Executing [s@macro-dial-one:33] ExecIf("Dongle/dongle0-0100000004", "0?Set(CHANNEL(musicclass)=)") in new stack
-- Executing [s@macro-dial-one:34] GosubIf("Dongle/dongle0-0100000004", "0?qwait,1()") in new stack
-- Executing [s@macro-dial-one:35] Set("Dongle/dongle0-0100000004", "CWIGNORE=") in new stack
-- Executing [s@macro-dial-one:36] Set("Dongle/dongle0-0100000004", "__KEEPCID=TRUE") in new stack
-- Executing [s@macro-dial-one:37] GotoIf("Dongle/dongle0-0100000004", "0?usegoto,1") in new stack
-- Executing [s@macro-dial-one:38] GotoIf("Dongle/dongle0-0100000004", "1?godial") in new stack
-- Goto (macro-dial-one,s,43)
-- Executing [s@macro-dial-one:43] Dial("Dongle/dongle0-0100000004", "SIP/1101,,Ttr") in new stack
== Using SIP RTP TOS bits 184
== Using SIP RTP CoS mark 5
-- Called SIP/1101
[2018-04-26 11:53:50] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 22
[2018-04-26 11:53:50] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 22
[2018-04-26 11:53:50] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 33
[2018-04-26 11:53:51] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 33
-- SIP/1101-00000002 is ringing
[2018-04-26 11:53:51] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 33
-- SIP/1101-00000002 is ringing
> 0x7fb21c032730 -- Strict RTP learning after remote address set to: 172.16.0.211:4002
[2018-04-26 11:54:02] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 33
[2018-04-26 11:54:02] WARNING[4440][C-00000006]: channel.c:1002 channel_indicate: [Dongle/dongle0-0100000004] Don't know how to indicate condition 22
-- SIP/1101-00000002 answered Dongle/dongle0-0100000004
> 0x7fb21c032730 -- Strict RTP switching to RTP remote address 172.16.0.211:4002 as source
[2018-04-26 11:54:02] ERROR[4423]: at_response.c:472 at_response_error: [dongle0] AT^DDSETEX failed
> 0x7fb21c032730 -- Strict RTP learning complete - Locking on source address 172.16.0.211:4002
-- Executing [h@macro-dial-one:1] Macro("Dongle/dongle0-0100000004", "hangupcall,") in new stack
-- Executing [s@macro-hangupcall:1] GotoIf("Dongle/dongle0-0100000004", "1?endmixmoncheck") in new stack
-- Goto (macro-hangupcall,s,20)
-- Executing [s@macro-hangupcall:20] NoOp("Dongle/dongle0-0100000004", "End of MIXMON check") in new stack
-- Executing [s@macro-hangupcall:21] GotoIf("Dongle/dongle0-0100000004", "1?nomeetmemon") in new stack
-- Goto (macro-hangupcall,s,39)
-- Executing [s@macro-hangupcall:39] NoOp("Dongle/dongle0-0100000004", "End of MEETME check") in new stack
-- Executing [s@macro-hangupcall:40] GotoIf("Dongle/dongle0-0100000004", "1?noautomon") in new stack
-- Goto (macro-hangupcall,s,45)
-- Executing [s@macro-hangupcall:45] NoOp("Dongle/dongle0-0100000004", "TOUCH_MONITOR_OUTPUT=") in new stack
-- Executing [s@macro-hangupcall:46] GotoIf("Dongle/dongle0-0100000004", "1?noautomon2") in new stack
-- Goto (macro-hangupcall,s,52)
-- Executing [s@macro-hangupcall:52] NoOp("Dongle/dongle0-0100000004", "MONITOR_FILENAME=") in new stack
-- Executing [s@macro-hangupcall:53] GotoIf("Dongle/dongle0-0100000004", "1?noautomon3") in new stack
-- Goto (macro-hangupcall,s,59)
-- Executing [s@macro-hangupcall:59] NoOp("Dongle/dongle0-0100000004", "MIXMONITOR_FILENAME=") in new stack
-- Executing [s@macro-hangupcall:60] GotoIf("Dongle/dongle0-0100000004", "1?noautomon4") in new stack
-- Goto (macro-hangupcall,s,62)
-- Executing [s@macro-hangupcall:62] NoOp("Dongle/dongle0-0100000004", "ONETOUCH_RECFILE=") in new stack
-- Executing [s@macro-hangupcall:63] NoOp("Dongle/dongle0-0100000004", "CDR recordingfile set to: ") in new stack
-- Executing [s@macro-hangupcall:64] GotoIf("Dongle/dongle0-0100000004", "1?skiprg") in new stack
-- Goto (macro-hangupcall,s,67)
-- Executing [s@macro-hangupcall:67] GotoIf("Dongle/dongle0-0100000004", "1?skipblkvm") in new stack
-- Goto (macro-hangupcall,s,70)
-- Executing [s@macro-hangupcall:70] GotoIf("Dongle/dongle0-0100000004", "1?theend") in new stack
-- Goto (macro-hangupcall,s,72)
-- Executing [s@macro-hangupcall:72] AGI("Dongle/dongle0-0100000004", "hangup.agi") in new stack
-- Launched AGI Script /var/lib/asterisk/agi-bin/hangup.agi
-- <Dongle/dongle0-0100000004>AGI Script hangup.agi completed, returning 0
-- Executing [s@macro-hangupcall:73] Hangup("Dongle/dongle0-0100000004", "") in new stack
== Spawn extension (macro-hangupcall, s, 73) exited non-zero on 'Dongle/dongle0-0100000004' in macro 'hangupcall'
== Spawn extension (macro-dial-one, h, 1) exited non-zero on 'Dongle/dongle0-0100000004'
== Spawn extension (macro-dial-one, s, 43) exited non-zero on 'Dongle/dongle0-0100000004' in macro 'dial-one'
== Spawn extension (macro-exten-vm, s, 7) exited non-zero on 'Dongle/dongle0-0100000004' in macro 'exten-vm'
== Spawn extension (default, 1101, 2) exited non-zero on 'Dongle/dongle0-0100000004'
-- Remote UNIX connection
-- Remote UNIX connection disconnected
issabelPBX*CLI>

and when I look at the characteristics of the dongle with dongle show device state dongle0 answers me this:

issabelPBX*CLI> dongle show device state dongle0
-------------- Status -------------
Device : dongle0
State : Free
Audio : /dev/ttyUSB0
Data : /dev/ttyUSB1
Voice : Yes
SMS : Yes
Manufacturer : huawei
Model : E156G
Firmware : 11.608.08.81.00
IMEI : 357133031008707
IMSI : 214075525622487
GSM Registration Status : Registered, home network
RSSI : 16, -81 dBm
Mode : No Service
Submode : No service
Provider Name : FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Location area code : 1236
Cell ID : 1163
Subscriber Number : Unknown
SMS Service Center : +34609090909
Use UCS-2 encoding : Yes
USSD use 7 bit encoding : No
USSD use UCS-2 decoding : Yes
Tasks in queue : 0
Commands in queue : 0
Call Waiting : Disabled
Current device state : start
Desired device state : start
When change state : now
Calls/Channels : 0
Active : 0
Held : 0
Dialing : 0
Alerting : 0
Incoming : 0
Waiting : 0
Releasing : 0
Initializing : 0

issabelPBX*CLI>

Thanks for the help you can give me

balkin77

My Issabel is dongled!!!!!!

thanks.

dariohimo

thanks, please write instalation by users new.

balkin77

Good morning, I just followed the instructions of the post that explains it, what happens is that I had a problem with the audio in the calls and I solved it by downloading a firmware version for my modem from another model with the same chip so that the voice function. I have a Huawei e156G modem, and I put the E160Update_11.609.10.02.432.B418.exe firmware version of an e160 model that carries the same chip.

Thank you all for your help, let's keep growing ...

emendoza

balkin77 you can help? here my post https://forum.issabel.org/d/405-chan-dongle/21

uogyuogy

jlebr
i have the same error do you have the soulution?
i cant download
rpm -ivh http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm
error
is there another link?

dariohimo

asterisk 13 your issabelpbx, and install asterisk11 dongle?

jlebr

dariohimo

hi my issabel is:
[root@issabel etc]# rasterisk -x "core show version"
Asterisk 13.22.0 built by issabel @ issabeldev8 on a x86_64 running Linux on 2018-08-30 13:58:00 UTC

and I want to install a huawei mobile broadband e173

[root@issabel etc]# lsusb
Bus 001 Device 007: ID 12d1:140c Huawei Technologies Co., Ltd. E180v
I want chan dongle to work
can you help?

dariohimo

chan_dongle-asterisk-11.25.0-rev34.x86_64

jlebr

dariohimo

it does not work

[root@issabel etc]# rpm -ivh http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm
Recuperando http://download.kingtelecom.com.br/download/chan_dongle-asterisk-11.25-0-rev34.x86_64.rpm
Error: Dependency error:
asterisk-devel is required by chan_dongle-asterisk-11.25.0-rev34.x86_64

dariohimo

the version package is chan_dongle-asterisk-11.25.0-rev34.x86_64 (asterisk11) your server is asterisk13.
not working different versions.
Os is centos 7, package install os.

jlebr

dariohimo

There is a more current version for chan_dongle-asterisk-11.25.0-rev34.x86_64 (asterisk11).

to work with my server?

ggrraay

jlebr you have to compile chan_dongle for your asterisk (just google howto) or reinstall your issabel and choose asterisk11 during installation.

ggrraay

emendoza Please post output of commands
lsusb
ls /dev/ttyUSB*