FAX Problem - ttyIAX1: Sending job 34 - [R] DIS/DTC received 3 times;

This site is best viewed in a modern browser with JavaScript enabled.

FAX Problem - ttyIAX1: Sending job 34 - [R] DIS/DTC received 3 times;

seederp2p

I'm using this with my SIP TRUNK and everything worked just fine before. I still can receive faxes but it seems I can't send.

Example of Hylafax Logs:

Oct 04 19:54:12.62: [10375]: SESSION BEGIN 000000082 0035122212XXXXXX
Oct 04 19:54:12.62: [10375]: HylaFAX (tm) Version 4.3.11
Oct 04 19:54:12.62: [10375]: SEND FAX: JOB 34 DEST 212XXXXXX COMMID 000000082 DEVICE '/dev/ttyIAX1' FROM 'Asterisk VoIP PBX <asterisk@localhost>' USER asterisk
Oct 04 19:54:12.62: [10375]: STATE CHANGE: RUNNING -> SENDING
Oct 04 19:54:12.62: [10375]: <-- [12:AT+FCLASS=1\r]
Oct 04 19:54:12.63: [10375]: --> [2K]
Oct 04 19:54:12.63: [10375]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Oct 04 19:54:12.63: [10375]: DIAL 212XXXXXX
Oct 04 19:54:12.63: [10375]: <-- [14:ATDT212XXXXXX\r]
Oct 04 19:54:29.44: [10375]: --> [7:CONNECT]
Oct 04 19:54:34.70: [10375]: --> [10:NO CARRIER]
Oct 04 19:54:34.70: [10375]: MODEM No carrier
Oct 04 19:54:34.70: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:54:34.78: [10375]: --> [2K]
Oct 04 19:54:34.78: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:54:34.80: [10375]: --> [7:CONNECT]
Oct 04 19:54:34.80: [10375]: <-- HDLC<3:FF C8 D8>
Oct 04 19:54:34.80: [10375]: <-- data [3]
Oct 04 19:54:34.80: [10375]: <-- data [2]
Oct 04 19:54:35.90: [10375]: --> [2K]
Oct 04 19:54:35.90: [10375]: SEND send CRP (command repeat)
Oct 04 19:54:35.90: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:36.58: [10375]: --> [7:CONNECT]
Oct 04 19:54:37.84: [10375]: --> HDLC<12:FF C0 04 61 00 C8 00 00 05 11 5B CF>
Oct 04 19:54:37.84: [10375]: --> [2K]
Oct 04 19:54:37.84: [10375]: REMOTE NSF "86 00 13 00 00 A0 88"
Oct 04 19:54:37.84: [10375]: NSF remote fax equipment: unknown
Oct 04 19:54:37.84: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:38.60: [10375]: --> [7:CONNECT]
Oct 04 19:54:38.60: [10375]: --> HDLC<25:FF C0 02 9C CC 2C 9C 0C 8C 4C 8C 4C 8C AC CC 04 04 04 04 04 04 04 04 19 1E>
Oct 04 19:54:38.60: [10375]: --> [2K]
Oct 04 19:54:38.60: [10375]: REMOTE CSI "351212XXXXXX"
Oct 04 19:54:38.60: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:39.07: [10375]: --> [7:CONNECT]
Oct 04 19:54:39.07: [10375]: --> HDLC<15:FF C8 01 04 77 15 23 01 C9 01 01 01 04 EE 63>
Oct 04 19:54:39.09: [10375]: --> [2K]
Oct 04 19:54:39.09: [10375]: REMOTE best rate 33600 bit/s
Oct 04 19:54:39.09: [10375]: REMOTE max A4 page width (215 mm)
Oct 04 19:54:39.09: [10375]: REMOTE max unlimited page length
Oct 04 19:54:39.09: [10375]: REMOTE best vres 300 x 300 dpi
Oct 04 19:54:39.09: [10375]: REMOTE format support: MH, MR, MMR, JBIG
Oct 04 19:54:39.09: [10375]: REMOTE supports T.30 Annex A, 256-byte ECM
Oct 04 19:54:39.09: [10375]: REMOTE best 10 ms/scanline
Oct 04 19:54:39.09: [10375]: USE 14400 bit/s
Oct 04 19:54:39.09: [10375]: USE error correction mode
Oct 04 19:54:39.09: [10375]: SEND file "docq/doc34.ps;c1"
Oct 04 19:54:39.09: [10375]: USE A4 page width (215 mm)
Oct 04 19:54:39.09: [10375]: USE unlimited page length
Oct 04 19:54:39.09: [10375]: USE 7.7 line/mm
Oct 04 19:54:39.09: [10375]: USE 2-D MMR
Oct 04 19:54:39.09: [10375]: USE 0 ms/scanline
Oct 04 19:54:39.09: [10375]: SEND training at v.17 14400 bit/s
Oct 04 19:54:39.09: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:54:39.19: [10375]: --> [2K]
Oct 04 19:54:39.19: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:54:39.21: [10375]: --> [7:CONNECT]
Oct 04 19:54:39.21: [10375]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:54:39.21: [10375]: <-- data [23]
Oct 04 19:54:39.21: [10375]: <-- data [2]
Oct 04 19:54:40.78: [10375]: --> [7:CONNECT]
Oct 04 19:54:40.78: [10375]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:54:40.78: [10375]: <-- data [7]
Oct 04 19:54:40.78: [10375]: <-- data [2]
Oct 04 19:54:41.19: [10375]: --> [2K]
Oct 04 19:54:41.19: [10375]: <-- [9:AT+FTS=7\r]
Oct 04 19:54:41.29: [10375]: --> [2K]
Oct 04 19:54:41.29: [10375]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:54:41.29: [10375]: <-- [11:AT+FTM=145\r]
Oct 04 19:54:41.31: [10375]: --> [7:CONNECT]
Oct 04 19:54:41.31: [10375]: DELAY 400 ms
Oct 04 19:54:41.71: [10375]: <-- data [1024]
Oct 04 19:54:41.71: [10375]: <-- data [1024]
Oct 04 19:54:41.71: [10375]: <-- data [652]
Oct 04 19:54:41.71: [10375]: <-- data [2]
Oct 04 19:54:44.33: [10375]: --> [2K]
Oct 04 19:54:44.33: [10375]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:54:44.33: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:44.35: [10375]: --> [7:CONNECT]
Oct 04 19:54:44.37: [10375]: --> [4:96 00 10 03]
Oct 04 19:54:44.37: [10375]: --> [5:ERROR]
Oct 04 19:54:44.37: [10375]: MODEM Command error
Oct 04 19:54:44.37: [10375]: FCS error
Oct 04 19:54:44.37: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:54:45.67: [10375]: --> [2K]
Oct 04 19:54:45.67: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:54:45.69: [10375]: --> [7:CONNECT]
Oct 04 19:54:45.69: [10375]: <-- HDLC<3:FF C8 D8>
Oct 04 19:54:45.69: [10375]: <-- data [3]
Oct 04 19:54:45.69: [10375]: <-- data [2]
Oct 04 19:54:46.79: [10375]: --> [2K]
Oct 04 19:54:46.79: [10375]: SEND send CRP (command repeat)
Oct 04 19:54:46.79: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:47.14: [10375]: --> [7:CONNECT]
Oct 04 19:54:48.38: [10375]: --> HDLC<12:FF C0 04 61 00 C8 00 00 05 11 5B CF>
Oct 04 19:54:48.38: [10375]: --> [2K]
Oct 04 19:54:48.38: [10375]: REMOTE NSF "86 00 13 00 00 A0 88"
Oct 04 19:54:48.38: [10375]: NSF remote fax equipment: unknown
Oct 04 19:54:48.38: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:49.16: [10375]: --> [7:CONNECT]
Oct 04 19:54:49.16: [10375]: --> HDLC<25:FF C0 02 9C CC 2C 9C 0C 8C 4C 8C 4C 8C AC CC 04 04 04 04 04 04 04 04 19 1E>
Oct 04 19:54:49.16: [10375]: --> [2K]
Oct 04 19:54:49.16: [10375]: REMOTE CSI "351212XXXXXX"
Oct 04 19:54:49.16: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:49.63: [10375]: --> [7:CONNECT]
Oct 04 19:54:49.63: [10375]: --> HDLC<15:FF C8 01 04 77 15 23 01 C9 01 01 01 04 EE 63>
Oct 04 19:54:49.65: [10375]: --> [2K]
Oct 04 19:54:49.65: [10375]: SEND training at v.17 14400 bit/s
Oct 04 19:54:49.65: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:54:49.75: [10375]: --> [2K]
Oct 04 19:54:49.75: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:54:49.77: [10375]: --> [7:CONNECT]
Oct 04 19:54:49.77: [10375]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:54:49.77: [10375]: <-- data [23]
Oct 04 19:54:49.77: [10375]: <-- data [2]
Oct 04 19:54:51.34: [10375]: --> [7:CONNECT]
Oct 04 19:54:51.34: [10375]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:54:51.34: [10375]: <-- data [7]
Oct 04 19:54:51.34: [10375]: <-- data [2]
Oct 04 19:54:51.74: [10375]: --> [2K]
Oct 04 19:54:51.74: [10375]: <-- [9:AT+FTS=7\r]
Oct 04 19:54:51.84: [10375]: --> [2K]
Oct 04 19:54:51.84: [10375]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:54:51.84: [10375]: <-- [11:AT+FTM=145\r]
Oct 04 19:54:51.86: [10375]: --> [7:CONNECT]
Oct 04 19:54:51.86: [10375]: DELAY 400 ms
Oct 04 19:54:52.27: [10375]: <-- data [1024]
Oct 04 19:54:52.27: [10375]: <-- data [1024]
Oct 04 19:54:52.27: [10375]: <-- data [652]
Oct 04 19:54:52.27: [10375]: <-- data [2]
Oct 04 19:54:54.88: [10375]: --> [2K]
Oct 04 19:54:54.88: [10375]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:54:54.88: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:55.49: [10375]: --> [7:CONNECT]
Oct 04 19:54:56.77: [10375]: --> HDLC<12:FF C0 04 61 00 C8 00 00 05 11 5B CF>
Oct 04 19:54:56.77: [10375]: --> [2K]
Oct 04 19:54:56.77: [10375]: REMOTE NSF "86 00 13 00 00 A0 88"
Oct 04 19:54:56.77: [10375]: NSF remote fax equipment: unknown
Oct 04 19:54:56.77: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:57.54: [10375]: --> [7:CONNECT]
Oct 04 19:54:57.54: [10375]: --> HDLC<25:FF C0 02 9C CC 2C 9C 0C 8C 4C 8C 4C 8C AC CC 04 04 04 04 04 04 04 04 19 1E>
Oct 04 19:54:57.54: [10375]: --> [2K]
Oct 04 19:54:57.54: [10375]: REMOTE CSI "351212XXXXXX"
Oct 04 19:54:57.54: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:54:58.01: [10375]: --> [7:CONNECT]
Oct 04 19:54:58.01: [10375]: --> HDLC<15:FF C8 01 04 77 15 23 01 C9 01 01 01 04 EE 63>
Oct 04 19:54:58.03: [10375]: --> [2K]
Oct 04 19:54:58.03: [10375]: SEND training at v.17 14400 bit/s
Oct 04 19:54:58.03: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:54:58.13: [10375]: --> [2K]
Oct 04 19:54:58.13: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:54:58.15: [10375]: --> [7:CONNECT]
Oct 04 19:54:58.15: [10375]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:54:58.15: [10375]: <-- data [23]
Oct 04 19:54:58.15: [10375]: <-- data [2]
Oct 04 19:54:59.71: [10375]: --> [7:CONNECT]
Oct 04 19:54:59.71: [10375]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:54:59.71: [10375]: <-- data [7]
Oct 04 19:54:59.71: [10375]: <-- data [2]
Oct 04 19:55:00.12: [10375]: --> [2K]
Oct 04 19:55:00.12: [10375]: <-- [9:AT+FTS=7\r]
Oct 04 19:55:00.22: [10375]: --> [2K]
Oct 04 19:55:00.22: [10375]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:55:00.22: [10375]: <-- [11:AT+FTM=145\r]
Oct 04 19:55:00.24: [10375]: --> [7:CONNECT]
Oct 04 19:55:00.24: [10375]: DELAY 400 ms
Oct 04 19:55:00.64: [10375]: <-- data [1024]
Oct 04 19:55:00.64: [10375]: <-- data [1024]
Oct 04 19:55:00.64: [10375]: <-- data [652]
Oct 04 19:55:00.64: [10375]: <-- data [2]
Oct 04 19:55:03.25: [10375]: --> [2K]
Oct 04 19:55:03.25: [10375]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:55:03.25: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:55:03.27: [10375]: --> [7:CONNECT]
Oct 04 19:55:03.31: [10375]: --> [4F 00 10 03]
Oct 04 19:55:03.31: [10375]: --> [5:ERROR]
Oct 04 19:55:03.31: [10375]: MODEM Command error
Oct 04 19:55:03.31: [10375]: FCS error
Oct 04 19:55:03.31: [10375]: <-- [9:AT+FRS=7\r]
Oct 04 19:55:04.59: [10375]: --> [2K]
Oct 04 19:55:04.59: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:55:04.61: [10375]: --> [7:CONNECT]
Oct 04 19:55:04.61: [10375]: <-- HDLC<3:FF C8 D8>
Oct 04 19:55:04.61: [10375]: <-- data [3]
Oct 04 19:55:04.61: [10375]: <-- data [2]
Oct 04 19:55:05.70: [10375]: --> [2K]
Oct 04 19:55:05.70: [10375]: SEND send CRP (command repeat)
Oct 04 19:55:05.70: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:55:06.39: [10375]: --> [7:CONNECT]
Oct 04 19:55:07.63: [10375]: --> HDLC<12:FF C0 04 61 00 C8 00 00 05 11 5B CF>
Oct 04 19:55:07.63: [10375]: --> [2K]
Oct 04 19:55:07.63: [10375]: REMOTE NSF "86 00 13 00 00 A0 88"
Oct 04 19:55:07.63: [10375]: NSF remote fax equipment: unknown
Oct 04 19:55:07.63: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:55:08.38: [10375]: --> [7:CONNECT]
Oct 04 19:55:08.38: [10375]: --> HDLC<25:FF C0 02 9C CC 2C 9C 0C 8C 4C 8C 4C 8C AC CC 04 04 04 04 04 04 04 04 19 1E>
Oct 04 19:55:08.38: [10375]: --> [2K]
Oct 04 19:55:08.38: [10375]: REMOTE CSI "351212XXXXXX"
Oct 04 19:55:08.38: [10375]: <-- [9:AT+FRH=3\r]
Oct 04 19:55:08.87: [10375]: --> [7:CONNECT]
Oct 04 19:55:08.87: [10375]: --> HDLC<15:FF C8 01 04 77 15 23 01 C9 01 01 01 04 EE 63>
Oct 04 19:55:08.89: [10375]: --> [2K]
Oct 04 19:55:08.89: [10375]: DIS/DTC received 3 times; DCS not recognized
Oct 04 19:55:08.89: [10375]: <-- [9:AT+FTH=3\r]
Oct 04 19:55:08.91: [10375]: --> [7:CONNECT]
Oct 04 19:55:08.91: [10375]: <-- HDLC<3:FF C8 DF>
Oct 04 19:55:08.91: [10375]: <-- data [3]
Oct 04 19:55:08.91: [10375]: <-- data [2]
Oct 04 19:55:10.00: [10375]: --> [2K]
Oct 04 19:55:10.00: [10375]: MODEM input buffering enabled
Oct 04 19:55:10.00: [10375]: <-- [5:ATH0\r]
Oct 04 19:55:10.12: [10375]: --> [2K]
Oct 04 19:55:10.12: [10375]: MODEM set DTR OFF
Oct 04 19:55:10.12: [10375]: MODEM set baud rate: 0 baud (flow control unchanged)
Oct 04 19:55:10.12: [10375]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Oct 04 19:55:10.12: [10375]: SESSION END

I Also get "RSRPEC error/got DCN" to a different number

Log:

Oct 04 19:58:42.90: [10721]: HylaFAX (tm) Version 4.3.11
Oct 04 19:58:42.90: [10721]: SEND FAX: JOB 35 DEST 229xxxxxx COMMID 000000084 DEVICE '/dev/ttyIAX1' FROM 'Asterisk VoIP PBX <asterisk@localhost>' USER asterisk
Oct 04 19:58:42.90: [10721]: STATE CHANGE: RUNNING -> SENDING
Oct 04 19:58:42.90: [10721]: <-- [12:AT+FCLASS=1\r]
Oct 04 19:58:42.90: [10721]: --> [2K]
Oct 04 19:58:42.90: [10721]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Oct 04 19:58:42.90: [10721]: DIAL 229xxxxxx
Oct 04 19:58:42.90: [10721]: <-- [14:ATDT229xxxxxx\r]
Oct 04 19:58:57.42: [10721]: --> [7:CONNECT]
Oct 04 19:59:02.70: [10721]: --> [10:NO CARRIER]
Oct 04 19:59:02.70: [10721]: MODEM No carrier
Oct 04 19:59:02.70: [10721]: <-- [9:AT+FRS=7\r]
Oct 04 19:59:02.76: [10721]: --> [2K]
Oct 04 19:59:02.76: [10721]: <-- [9:AT+FTH=3\r]
Oct 04 19:59:02.78: [10721]: --> [7:CONNECT]
Oct 04 19:59:02.78: [10721]: <-- HDLC<3:FF C8 D8>
Oct 04 19:59:02.78: [10721]: <-- data [3]
Oct 04 19:59:02.78: [10721]: <-- data [2]
Oct 04 19:59:03.88: [10721]: --> [2K]
Oct 04 19:59:03.88: [10721]: SEND send CRP (command repeat)
Oct 04 19:59:03.88: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:09.01: [10721]: --> [7:CONNECT]
Oct 04 19:59:10.31: [10721]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Oct 04 19:59:10.31: [10721]: --> [2K]
Oct 04 19:59:10.31: [10721]: REMOTE NSF "AD 00 36 A0 00 00 00 00"
Oct 04 19:59:10.31: [10721]: NSF remote fax equipment: HP
Oct 04 19:59:10.31: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:11.01: [10721]: --> [7:CONNECT]
Oct 04 19:59:11.01: [10721]: --> HDLC<25:FF C0 02 9C EC 6C 9C CC 2C 9C 4C 4C 04 04 04 04 04 04 04 04 04 04 04 EF E0>
Oct 04 19:59:11.01: [10721]: --> [2K]
Oct 04 19:59:11.01: [10721]: REMOTE CSI "229xxxxxx"
Oct 04 19:59:11.01: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:11.45: [10721]: --> [7:CONNECT]
Oct 04 19:59:11.45: [10721]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 19 00 3A A4>
Oct 04 19:59:11.48: [10721]: --> [2K]
Oct 04 19:59:11.48: [10721]: REMOTE best rate 14400 bit/s
Oct 04 19:59:11.48: [10721]: REMOTE max A4 page width (215 mm)
Oct 04 19:59:11.48: [10721]: REMOTE max unlimited page length
Oct 04 19:59:11.48: [10721]: REMOTE best vres 300 x 300 dpi
Oct 04 19:59:11.48: [10721]: REMOTE format support: MH, MR, MMR, JPEG Full-Color
Oct 04 19:59:11.48: [10721]: REMOTE supports T.30 Annex A, 256-byte ECM
Oct 04 19:59:11.48: [10721]: REMOTE best 0 ms/scanline
Oct 04 19:59:11.48: [10721]: USE 14400 bit/s
Oct 04 19:59:11.48: [10721]: USE error correction mode
Oct 04 19:59:11.48: [10721]: SEND file "docq/doc35.ps;c1"
Oct 04 19:59:11.48: [10721]: USE A4 page width (215 mm)
Oct 04 19:59:11.48: [10721]: USE unlimited page length
Oct 04 19:59:11.48: [10721]: USE 7.7 line/mm
Oct 04 19:59:11.48: [10721]: USE 2-D MMR
Oct 04 19:59:11.48: [10721]: USE 0 ms/scanline
Oct 04 19:59:11.48: [10721]: SEND training at v.17 14400 bit/s
Oct 04 19:59:11.48: [10721]: <-- [9:AT+FRS=7\r]
Oct 04 19:59:11.60: [10721]: --> [2K]
Oct 04 19:59:11.60: [10721]: <-- [9:AT+FTH=3\r]
Oct 04 19:59:11.62: [10721]: --> [7:CONNECT]
Oct 04 19:59:11.62: [10721]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:59:11.62: [10721]: <-- data [23]
Oct 04 19:59:11.62: [10721]: <-- data [2]
Oct 04 19:59:13.19: [10721]: --> [7:CONNECT]
Oct 04 19:59:13.19: [10721]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:59:13.19: [10721]: <-- data [7]
Oct 04 19:59:13.19: [10721]: <-- data [2]
Oct 04 19:59:13.60: [10721]: --> [2K]
Oct 04 19:59:13.60: [10721]: <-- [9:AT+FTS=7\r]
Oct 04 19:59:13.70: [10721]: --> [2K]
Oct 04 19:59:13.70: [10721]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:59:13.70: [10721]: <-- [11:AT+FTM=145\r]
Oct 04 19:59:13.72: [10721]: --> [7:CONNECT]
Oct 04 19:59:13.72: [10721]: DELAY 400 ms
Oct 04 19:59:14.12: [10721]: <-- data [1024]
Oct 04 19:59:14.12: [10721]: <-- data [1024]
Oct 04 19:59:14.12: [10721]: <-- data [652]
Oct 04 19:59:14.12: [10721]: <-- data [2]
Oct 04 19:59:16.73: [10721]: --> [2K]
Oct 04 19:59:16.73: [10721]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:59:16.73: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:17.14: [10721]: --> [7:CONNECT]
Oct 04 19:59:18.46: [10721]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Oct 04 19:59:18.46: [10721]: --> [2K]
Oct 04 19:59:18.46: [10721]: REMOTE NSF "AD 00 36 A0 00 00 00 00"
Oct 04 19:59:18.46: [10721]: NSF remote fax equipment: HP
Oct 04 19:59:18.46: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:19.16: [10721]: --> [7:CONNECT]
Oct 04 19:59:19.16: [10721]: --> HDLC<25:FF C0 02 9C EC 6C 9C CC 2C 9C 4C 4C 04 04 04 04 04 04 04 04 04 04 04 EF E0>
Oct 04 19:59:19.16: [10721]: --> [2K]
Oct 04 19:59:19.16: [10721]: REMOTE CSI "229xxxxxx"
Oct 04 19:59:19.16: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:19.60: [10721]: --> [7:CONNECT]
Oct 04 19:59:19.60: [10721]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 19 00 3A A4>
Oct 04 19:59:19.62: [10721]: --> [2K]
Oct 04 19:59:19.62: [10721]: SEND training at v.17 14400 bit/s
Oct 04 19:59:19.62: [10721]: <-- [9:AT+FRS=7\r]
Oct 04 19:59:19.73: [10721]: --> [2K]
Oct 04 19:59:19.73: [10721]: <-- [9:AT+FTH=3\r]
Oct 04 19:59:19.75: [10721]: --> [7:CONNECT]
Oct 04 19:59:19.75: [10721]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:59:19.75: [10721]: <-- data [23]
Oct 04 19:59:19.75: [10721]: <-- data [2]
Oct 04 19:59:21.31: [10721]: --> [7:CONNECT]
Oct 04 19:59:21.31: [10721]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:59:21.31: [10721]: <-- data [7]
Oct 04 19:59:21.31: [10721]: <-- data [2]
Oct 04 19:59:21.72: [10721]: --> [2K]
Oct 04 19:59:21.72: [10721]: <-- [9:AT+FTS=7\r]
Oct 04 19:59:21.82: [10721]: --> [2K]
Oct 04 19:59:21.82: [10721]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:59:21.82: [10721]: <-- [11:AT+FTM=145\r]
Oct 04 19:59:21.84: [10721]: --> [7:CONNECT]
Oct 04 19:59:21.84: [10721]: DELAY 400 ms
Oct 04 19:59:22.24: [10721]: <-- data [1024]
Oct 04 19:59:22.24: [10721]: <-- data [1024]
Oct 04 19:59:22.24: [10721]: <-- data [652]
Oct 04 19:59:22.24: [10721]: <-- data [2]
Oct 04 19:59:24.85: [10721]: --> [2K]
Oct 04 19:59:24.85: [10721]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:59:24.85: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:25.26: [10721]: --> [7:CONNECT]
Oct 04 19:59:26.58: [10721]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Oct 04 19:59:26.58: [10721]: --> [2K]
Oct 04 19:59:26.58: [10721]: REMOTE NSF "AD 00 36 A0 00 00 00 00"
Oct 04 19:59:26.58: [10721]: NSF remote fax equipment: HP
Oct 04 19:59:26.58: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:27.27: [10721]: --> [7:CONNECT]
Oct 04 19:59:27.27: [10721]: --> HDLC<25:FF C0 02 9C EC 6C 9C CC 2C 9C 4C 4C 04 04 04 04 04 04 04 04 04 04 04 EF E0>
Oct 04 19:59:27.27: [10721]: --> [2K]
Oct 04 19:59:27.27: [10721]: REMOTE CSI "229xxxxxx"
Oct 04 19:59:27.27: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:27.72: [10721]: --> [7:CONNECT]
Oct 04 19:59:27.72: [10721]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 19 00 3A A4>
Oct 04 19:59:27.74: [10721]: --> [2K]
Oct 04 19:59:27.74: [10721]: SEND training at v.17 14400 bit/s
Oct 04 19:59:27.74: [10721]: <-- [9:AT+FRS=7\r]
Oct 04 19:59:27.84: [10721]: --> [2K]
Oct 04 19:59:27.84: [10721]: <-- [9:AT+FTH=3\r]
Oct 04 19:59:27.86: [10721]: --> [7:CONNECT]
Oct 04 19:59:27.86: [10721]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Oct 04 19:59:27.86: [10721]: <-- data [23]
Oct 04 19:59:27.86: [10721]: <-- data [2]
Oct 04 19:59:29.43: [10721]: --> [7:CONNECT]
Oct 04 19:59:29.43: [10721]: <-- HDLC<7:FF C8 C1 00 46 1F 22>
Oct 04 19:59:29.43: [10721]: <-- data [7]
Oct 04 19:59:29.43: [10721]: <-- data [2]
Oct 04 19:59:29.83: [10721]: --> [2K]
Oct 04 19:59:29.83: [10721]: <-- [9:AT+FTS=7\r]
Oct 04 19:59:29.93: [10721]: --> [2K]
Oct 04 19:59:29.93: [10721]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Oct 04 19:59:29.93: [10721]: <-- [11:AT+FTM=145\r]
Oct 04 19:59:29.95: [10721]: --> [7:CONNECT]
Oct 04 19:59:29.95: [10721]: DELAY 400 ms
Oct 04 19:59:30.35: [10721]: <-- data [1024]
Oct 04 19:59:30.35: [10721]: <-- data [1024]
Oct 04 19:59:30.35: [10721]: <-- data [652]
Oct 04 19:59:30.35: [10721]: <-- data [2]
Oct 04 19:59:32.96: [10721]: --> [2K]
Oct 04 19:59:32.96: [10721]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Oct 04 19:59:32.96: [10721]: <-- [9:AT+FRH=3\r]
Oct 04 19:59:33.39: [10721]: --> [7:CONNECT]
Oct 04 19:59:34.48: [10721]: --> HDLC<5:FF C8 5F C8 E7>
Oct 04 19:59:34.50: [10721]: --> [2K]
Oct 04 19:59:34.50: [10721]: TRAINING failed
Oct 04 19:59:34.50: [10721]: <-- [9:AT+FTH=3\r]
Oct 04 19:59:34.52: [10721]: --> [7:CONNECT]
Oct 04 19:59:34.52: [10721]: <-- HDLC<3:FF C8 DF>
Oct 04 19:59:34.52: [10721]: <-- data [3]
Oct 04 19:59:34.52: [10721]: <-- data [2]
Oct 04 19:59:35.62: [10721]: --> [2K]
Oct 04 19:59:35.62: [10721]: MODEM input buffering enabled
Oct 04 19:59:35.62: [10721]: <-- [5:ATH0\r]
Oct 04 19:59:35.74: [10721]: --> [2K]
Oct 04 19:59:35.74: [10721]: MODEM set DTR OFF
Oct 04 19:59:35.74: [10721]: MODEM set baud rate: 0 baud (flow control unchanged)
Oct 04 19:59:35.74: [10721]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Oct 04 19:59:35.74: [10721]: SESSION END

Any hint?

PS: I Ommited the destination numbers